How to Install a Ghost Immobiliser
ghost ii immobiliser immobilisers are hidden security system that shields your car from hacking and key cloning. It works by stopping the engine from running until it is activated using PIN codes, which can be up to 20 characters long.
It is unnoticeable by thieves who don't expect this extra layer of security. Certain systems come with an app that allows the owner to disable their immobiliser if they forget their PIN number or utilize the service/valet mode.
Connecting the vehicle's CAN Bus to the vehicle's
The Ghost 2 Immobiliser, a cutting edge security system, can be incorporated directly into the ECU of your vehicle. It offers a discrete barrier against thieves. It is highly efficient and user-friendly. This makes it a valuable asset to your vehicle's security arsenal. Like all anti-theft devices it's not foolproof and requires regular maintenance in order to function effectively. This guide will help you get the most of your
ghost immobiliser birmingham 2 immobiliser.
CAN (Controller Area Network) is a reliable serial networking, allows microcontrollers communicate with each other over short distances. Central control units is not required. It is designed to allow multiplexing of electrical wiring within vehicles to save on copper and has a number of advantages, such as low cost and ease of use.
The CAN protocol is utilized in the majority of modern vehicles to communicate with the engine management system, transmission controller, steering control module and air conditioning controls and more. It also transmits data from sensors like inputs and speed sensors, to control the various functions of the car. The CAN bus is used to monitor these various components, and prevent a vehicle from starting if they are in an unsafe state.
It's crucial to understand how the CAN bus functions and how it's secured. It is possible to add additional features to vehicles using CAN bus, but it's crucial to safeguard it from threats from hackers and other types. The best method to achieve this is to install a firewall and monitoring your CAN bus through software.
Ghost2's control device is hidden within the dashboard or wiring harness, preventing thieves from physically tampering with it. It is impossible to reset a pin code or an emergency code without having access to the car.
If you have to give your car away to a valet parking service, maintenance or for any other reason, you can turn on the Transport Mode. This feature disables both the keyfob as well as the ignition functions of the Ghost immobiliser. It will only be activated after the car has reached 31 mph for a time of 15 minutes.
How do I create a PIN code
The Ghost immobiliser is a robust security system that guards your vehicle from thieves. The revolutionary technology utilizes the PIN to shut down the vehicle's engine and prevent it from starting without the right code, or a valid fob or mobile. Its discreet design ensures that the system is not noticed and provides unrivaled security against theft. Moreover the system is TASSA verified and can result in significant savings on insurance premiums for cars.
During installation, Ghost enters a "learning mode" to record the sequence of buttons that are that are pressed to generate your unique pin codes. The installer will guide you through activating the system once the pin code has been created. Once activated it will Ghost system will disable the motor that starts your vehicle until a valid PIN has been entered or the vehicle is switched into transport mode. This makes it extremely difficult for thieves to duplicate or hack your vehicle's starter system.
It is simple to install an easy-to-install
ghost immobiliser 2 immobiliser, but you must follow the detailed instructions in the user's guide to ensure that it is operating properly. Hand tools and multimeters can be used to check electrical values. Insulation tape, heat shrink tubing and cable ties can be utilized to protect exposed wiring. Also, make sure to test the system frequently to spot any problems and potential errors.
After the installation is completed after the installation is complete, you must perform a final check of the system before turning on your vehicle's ignition. The Ghost immobiliser will arm itself after 3 to 30 seconds, depending on your car's model. The system also has a Service/Valet mode that allows you to temporarily disable the system while you are servicing your vehicle or parking valet.
Ideally, the immobiliser should be hidden beneath the dashboard or on the steering wheel. It is recommended to use a small bit of paint or duct tape to mark the CAN H and CAN L wires so that you can easily identify them when you are testing. The CAN H and the L wires should also be connected to an electrical source that delivers continuous 12V. It is also crucial to re-check the connections after testing, as misidentifying these wires can cause the system to malfunction.
Activating the system
A ghost immobiliser prevents the car from starting unless you press certain buttons in the vehicle, typically on the steering wheel or the door panel, or the central console. The sequence is set by the user and can be altered at any time. Once the system is activated, it cannot be deactivated by thieves which makes it a great option for anyone looking to secure their vehicle from theft.
The system is designed to be undetectable, which means it isn't detected by modern diagnostics or code-grabbing technologies. It also does not send radio signals which makes it harder for thieves to detect the device.
If the device is located it will stop the engine from running. It will also sound an alarm to scare thieves away. The device can be used to monitor a car's location and assist in the recovery of the vehicle in case it is stolen.
Contact Car Specalist Customs for a estimate or to discuss your options if you're interested in a
Ghost Immobiliser 2 immobiliser. We are fully certified to install a ghost
immobiliser ghost for your vehicle, and will make sure that it is tucked away in a remote area. We can also install additional security measures, including a kill switch and wheel lock to protect your vehicle from theft.
Disarming the System
If you own a Ghost immobiliser that is fitted to your vehicle, it's vital to know how to disable it. This will aid you in the event that you lock your keys in the car or if your battery dies. The system uses an individual PIN code that only you know, and the immobiliser will not start your vehicle unless you enter this code. The simplest method to enter the code is to press a combination of buttons on your dashboard or the steering wheel. This is a simpler method than using the key fob and also stops anyone from copying your remote.
Contrary to other aftermarket immobilisers which require cutting wires for installation, Ghost2 is non-invasive and is compatible with your vehicle's bus network to function. Its standout characteristic is its ability to bypass the engine without affecting the normal functions, making it difficult for thieves to make use of signal boosters or clone your car key. It does not emit radio frequencies, which means thieves are unable to detect it.
The Ghost system also has the Transport Mode which allows you to temporarily disable the security system in circumstances like transportation or servicing. This is a great option if you have to lend your vehicle to someone without sharing the PIN number or in case you wish to ensure your vehicle is secure while driving it. Press the service button five times over 2 seconds to activate Transport Mode. The Ghost system will confirm activation via 5 signal signals.
Save the emergency code outside your vehicle in a safe place.