Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to professional auto locksmiths who have the right equipment and technical know-how. They will be able to create and program new keys quicker than a dealership and at a cheaper cost.
If the key fob stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are also other reasons that the key might be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. If this is the scenario, you'll need apply the backup starting technique that's described in the owner's manual for your vehicle.
Another reason your 208 might not be starting is because the spark plugs have been damaged. The spark plugs are responsible for instigating the fuel that powers the engine. However they are limited in their life span. If they aren't used enough they will eventually fail.
There is a simple solution to this issue. Examine the voltage of your battery with a multimeter. If the voltage is below 11,5 volts, it's time to replace it. It is also necessary to clean the battery's contacts in the event that it is damaged by corrosion. This can be done by lifting the rubber covers that protect the two terminals of the battery and using a wire brush to remove any parts that are corroded from the battery. Then, reconnect the cables that connect the positive and negative poles.
Water Damage
If your 208 does not start and the battery hasn't been replaced, you must inspect the spark plugs. It is possible that they are just overly dirty, causing them not to spark. This is easily fixed by cleaning the spark plugs in the workshop.
Peugeot cars are equipped with a transponder key that works with the car's ignition system. This ensures only the correct key can turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the correct signal to the vehicle.
This is a very common issue that is caused by water damage. This is a typical issue in colder climates where the vehicle is exposed to snow or rain. In this case, you need to contact an experienced locksmith who will have the tools and equipment required to reprogram the key. They will also have all the latest technology and equipment needed to make a Peugeot smart key. The process shouldn't take longer than 15 minutes.
Contacts of the battery may be damaged.
Peugeot changed from the old carbon-encased transponder chips and introduced a new type of chip that incorporates electronic components that are placed on circuit boards. This new system works well when it's new, however, over time, the circuit boards start to wear out and stop functioning properly.
This could prevent the immobiliser chip from activating and causing your car to not start. Contact an
peugeot car key not working specialist or a locksmith, if this is the situation.
Another issue that is common is when the battery in the key fob begins to fail, which causes the key blade to stop getting into the lock. A locksmith in your car will replace the battery, and cut a new blade for you. This is a quick solution.
Faulty Receiver Module
It could be that the receiver module has a problem in the event that your Peugeot key fob fails to function after being dropped on the floor, or exposed to a sudden rainstorm or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer that controls the central locking system in your Peugeot vehicle.
The key fob itself has rubber seals to prevent water from reaching the electronic chip inside. Water can damage the chip when it is exposed to water for a prolonged period of time. Submerging the key fob into sea water at the beach or throwing it into the pool can be particularly damaging due to the high salt content.
The module will need to be replaced if your Peugeot spare key isn't working anymore. This is only done by an expert auto locksmith or
peugeot partner van key fob specialist. Peugeot keys like other cars are secured by an immobilizer device. This requires the correct coding to start the car. This is why you must trust an experienced Peugeot locksmith to handle the task of creating and programming a replacement.
Computer malfunctioning on-board
The computer on board in your Peugeot is the one responsible for all of the systems inside your vehicle, from airbags to power windows. If something is wrong with these systems, they will usually display a code that identifies the problem. This code is stored in the system and will remain there until the problem is resolved. Often, this will involve replacing the computer on board.
The most common reason for the warning light for the airbag to illuminate is corrosion or loose connections within the sensor. This could be due to wear and tear, aging, or exposure to moisture and salt. This problem should be taken care of as soon as you can, as an airbag that's malfunctioning could be dangerous in case in the event of an accident.
If your Peugeot is showing a card detected as not present error then the key battery inside the key fob might be dead or weak. This can prevent the key fob from sending a signal that disables your vehicle's immobilizer. Try this by pressing the unlock button on the key fob and then trying to start your car. If it doesn't work it is because the battery of the key needs to be replaced.