Reasons Why Your Nissan Qashqai Key Fob Won't Work
The Qashqai has a distinct SUV feel to it thanks to its bigger dimensions, and the wheel sizes of 19 inches in Ti and ST-L models can be firm at times. The front tyres of the Qashqai can lose grip on rough surfaces, and its CVT can occasionally display wrist-flexing torque steer.
It is usually caused by an unresponsive coin battery that can be easily replaced in just a few minutes. Make sure that the replacement battery is the same size, voltage and specifications.
Water Damage
One of the most common reasons that a
nissan hardbody key key fob might display the "key ID is not correct" message is due to water damage. The key fob has rubber seals that protect the electronic chip inside, however prolonged exposure to moisture could cause it to stop functioning properly. It's common to see this when your key fob has been dropped in the ocean or swimming pool. However, it could also occur when it is wet from rain or soapy hands.
If your key fob is exposed to water for an extended period of time, it could need to be cleaned using isopropyl alcohol or electronic cleaner. Or, it could require taking to a professional for repair or replacement.
If your key fob has to be replaced, it is an easy process. First, ensure you have a multipack of the right battery (CR2032 3V). Open the front and rear cases with a flathead screwdriver. Remove the metal clips, remove the battery that was in place and replace it. Reassemble the fob and replace the mechanical key. Make sure it's working properly. If it does not, you will need to go to your local
nissan 350z key dealer or an experienced auto locksmith to repair the chip in the key. The chip isn't usually damaged by water and therefore isn't too costly.
Dead Coin Battery
The coin battery is another common reason for why your
nissan key programmer Qashqai remote key fob might not function. They last for 3 to 5 years, but they can become faulty over time when the fob is frequently dropped. You can replace the battery however, make sure it's the same voltage and the same size as the original. If you use a different battery it may cause the key to have an untrue key ID, which will prevent it from connecting to your vehicle.
The most efficient method to change the battery inside the Nissan Qashqai Key Fob is to pry it open with an small screwdriver that has a flat head. The screwdriver needs to be inserted into a small cut on the bottom of the key fob. Simply twist the screwdriver to divide the two halves. Then, remove the old CR2025 button cell battery and insert a new one after noting its position in the fob.
Before putting the new battery in place check to ensure there is no dirt or water damage to the terminals. If there is, wash the terminals using a small amount of isopropyl alcohol. You'll also need to ensure that the pole cables are connected correctly - they should be connected to the negative and positive poles of the battery respectively.
Troubleshooting
If your Nissan Qashqai key fob stops working after exposure to clean rain or tap water it could be an indication of an internal chip issue. You'll require a new keyfob if you can't resolve the issue by replacing the battery. If you dropped the key fob on the ground and it stopped working right away it's likely because it has damaged the internal chip. It is usually possible to get the key fob back to function again if you take it out and clean the chip with alcohol and paper towels and then put it back into.
A common error that you may see on your dashboard is "Key ID Not Correct." The vehicle is unable to recognize the key fob, and consequently, won't allow the car to start. This can happen in various ways, including water damage, issues that are undetectable in the key fob's circuitry or RFID interference.
If the 12 volt battery in your key fob is dead or not providing sufficient electric current it will cease to function. This could affect the
nissan micra key price Qashqai's remote keyless system central locking, as well as the ability to start the engine with the key fob. If you're unable to unlock or lock the door by hand you must check the batteries inside your key fob and make sure they are in good condition. Try re-inserting the battery to reset the transmitter.
Reprogramming
If the key fob was not submerged into saltwater, it should be able be restored to its original state with a simple rinse of clean water. You can also clean the electronic chip using isopropyl or electronic cleaner. If none of these works it could be time to replace the entire key fob with a new one.
If your
nissan keys made Intelligent Key is still not working, there could be a problem with the connection between it and the car. Start by turning the ignition key but not beginning the car. Continue doing this until you see the warning lights flash twice. Then, turn the car off and remove the keys.
Next, you must open the fob compartment inside your vehicle. It's usually found on a door's jamb or the handle of the driver's door. Find the small "program" button and press it. You will hear a sound once the process is complete.
It's time to test your Intelligent Key to the test. Make sure you press all the buttons on the key while standing at a distance from the vehicle. If the lights flash, or the horn sounds, the key is connected to the
nissan spare key. You may also try testing the key in close proximity.